Electric G tractor conversion
Summary: The Allis Chalmers G tractor was built in the late 1940′s to be a cultivating tractor, using a relatively low horespower gasoline engine that is bolted to the back of the tractor’s frame to allow the operator a clear view of the implements mounted on the belly of the tractor. It’s a great tractor for cultivating, but over time the engines can fall further and further out of good repair.
Farmer (and inventor!) Ron Khosla came up with instructions to convert these tractors to run on an electric motor and heavy duty batteries, giving you a fully functional, easy-to-maintain, quiet, no-emissions tractor. These electric G’s work great for cultivating, seeding, and some tinkerers have even rigged them up to do tillage and mowing.
How to build it:
A complete set of step-by-step instructions and materials list is maintained by the original author, Ron Khosla, at the Electric G web site.
There are various features that can be added on to this project. For example, the standard conversion is done with a 48v motor and four 12v batteries. If you want to have more “juice” there are a couple of options. You can use a 72v motor and more batteries, which will give you more power to do heavier work. If your preference is to work longer on a charge, you can use more battery mass– for example, on a 48v system, use eight 6v batteries, or six 8v batteries, which gives you the same voltage, but more mass, i.e. more lead and acid since all of these batteries are about the same size and weight regardless of voltage, which means more energy. The tractor in the photo at the top of the post, from 47th Avenue Farm in Oregon, has six 8v batteries; the photo to the left, from Mountain Bounty Farm in Nevada City, CA, has a whopping eight 6v batteries, which caused the back end to be so heavy that they had to strap some iron ballast to the front to even things out!
If the mechanical hydraulics on your G still work (driven by a hydraulic pump powered by the drive train) you can use them– that’s what I do on mine. However, many people choose to add an electrically powered hydraulic pump to power the belly and rear hydraulic cylinders. These are usually 12v pumps, so many people will add a 12v battery into the mix exclusively to power this pump. See this setup on the photo to the right, the G at Persephone Farm in Lebanon, Oregon. Having your hydraulics set up like this means that you can operate them without sending power to the tractor’s motor; the hydraulics run very quickly and efficiently this way.
It’s also possible to re-charge your tractor using solar panels, or other sources of electricity generation. However, these batteries are quite cheap to charge using grid power– Ron Khosla estimated that his cost him $12 of electricity per year to recharge– and setting up solar will probably cost a couple thousand dollars, so it’s hard to justify unless you don’t have easy access to grid power.
How to use it:
An electric G works just like a gasoline G, with a few exceptions. Because there is no need for the electric motor to idle like a gasoline engine, there is no need for a clutch to detach the transmission from the engine. To change gears, you just stop the motor and shift. The tractor can be used for several hours before a recharge is needed; of course, it depends on how you’re using it. We have only once run out of juice while cultivating on our farm, in 3 years. Also, we once got caught in a rain storm on our electric tractor; some water got into the controller, and it didn’t like that. But you shouldn’t be cultivating in the rain anyway.
The most important thing to remember with these electric tractors is to maintain the batteries very very carefully. This means recharging them immediately after use, every night; a battery that’s not at full charge begins to build up sulfation, which weakens its life significantly. It’s also important to monitor the level of sulfuric acid in your battery cells. And ideally you shouldn’t run your batteries all the way down to zero charge when using them, this also leads to early sulfation.
Actually, the most important thing to remember is that you’re dealing with a lot of voltage on these, and it’s very important to take safety precautions to ensure that you don’t get hurt or destroy your batteries or components. Follow the directions carefully and you should be ok.